(Click here to buy membrane<\/em>)<\/li>\n<\/ul>\n\n\n\nWhy Booster Pump Failures Make Air<\/h2>\n\n\n\n Boosters suck in air when there is not enough water in the suction chamber.<\/strong> This causes the pump to make air during operation. Also, if the air in the expansion tank is missing or the membrane is burst, the booster makes noise.<\/strong><\/p>\n\n\n\nBooster Works Intermittently<\/h2>\n\n\n\n There are several reasons why your booster may run intermittently. Some of these are as follows:<\/p>\n\n\n\n
\nThe check valve in the suction line is leaking<\/strong>.<\/li>\n\n\n\nIf your booster is a spherical booster, the air in the membrane in the sphere has disappeared or the balloon has burst<\/strong>.<\/li>\n\n\n\nPump internal assembly elements are damaged<\/strong>.<\/li>\n<\/ul>\n\n\n\nIf your booster is running continuously or if it is activated at frequent intervals, it is an indication that the pressure is low or that the damper has burst.<\/p>\n\n\n\n
If the booster is running continuously, you can remove the valve cover on the tank and press on the valve using an object such as a pen.<\/strong><\/p>\n\n\n\nBooster Booster Malfunctions Continuously Running<\/h2>\n\n\n\n If the booster is running continuously<\/strong>, you can remove the valve cover on the tank and press the valve using an object such as a pencil to see if there is any burst<\/strong>.<\/p>\n\n\n\nWhat happens if the booster is constantly running, the booster is constantly running, it does not pump water. Why the booster motor burns out, if the water pump is running but does not pump water. <\/p>\n\n\n\n
The pump burns out as a result of long-term behavior in this way. So why the booster works continuously, let’s look at the reasons why the booster is constantly activated.<\/p>\n\n\n\n
If the booster is occasionally running on its own even though there is no water use<\/strong>, there may be several reasons for this situation:<\/p>\n\n\n\n\nThere is a leakage greater than 70 liters\/hour flow rate at any point of the installation<\/strong>.<\/li>\n\n\n\nThe manual start button (RESET) is stuck<\/strong>.<\/li>\n\n\n\nElectronic board failure<\/strong>.<\/li>\n\n\n\nFaulty electrical connection<\/strong><\/li>\n<\/ul>\n\n\n\nBooster Pressure Switch Failure Cause Prevention Way<\/h2>\n\n\n\n Booster pressure switch malfunction, the cause of the booster not operating or operating at low pressure. It controls the working pressure of the booster. If it is faulty, the booster will not operate or will operate at low pressure.<\/p>\n\n\n\n
In order to prevent malfunction, periodic maintenance of<\/strong> the booster is required. During booster maintenance, it is important to check the pressure switch and replace it when necessary. The booster pressure switch remains stuck,<\/p>\n\n\n\nAlso, the water level<\/strong> in the water tank must be sufficient<\/strong> during booster operation. If the water level in the water tank is not sufficient, the booster will not operate or will operate at low pressure.<\/p>\n\n\n\nFor more information on booster pressure switch repair<\/strong>, please consult a specialist.<\/p>\n\n\n\nThe booster does not pump water even though it works normally, there is heating in the electric motor!<\/strong><\/h2>\n\n\n\nWe can try the following steps for problems such as the booster does not flood, why the booster does not flood, the booster works but does not flood.<\/p>\n\n\n\n
\nThe water in the tank is empty. Do not start the booster until the tank is full of water.<\/li>\n\n\n\n The hydrophore is drawing air from the suction line. Check the suction line.<\/li>\n\n\n\n The valve on the suction line is closed. Open it.<\/li>\n\n\n\n The filter in the suction line is clogged. Clean it.<\/li>\n\n\n\n The pump has air in it. Notify the authorized technical service.<\/li>\n\n\n\n The motor is reversing. Notify the authorized technical service. Contact without thinking for all booster malfunctions that you need to notify the authorized service.<\/li>\n<\/ul>\n\n\n\nIt does not work even though the pressure drops after stopping automatically!<\/strong><\/h2>\n\n\n\n\nThe pressure switch is defective. Replace it. If you think you cannot replace it yourself, contact the technical service.<\/li>\n<\/ul>\n\n\n\nThe motor is whining and the pump won’t turn!<\/strong><\/h2>\n\n\n\n
\nIf the motor is three-phase<\/strong>, one of the phases is not coming. Check the fuse and switch.<\/li>\n\n\n\nIf the motor is single-phase<\/strong>, the capacitor is broken<\/li>\n\n\n\nThe engine is stuck.<\/li>\n<\/ul>\n\n\n\nIn these 3 cases, please contact the authorized service for booster malfunctions.<\/p>\n\n\n\n
Electric Booster Failures<\/h2>\n\n\n\n If you are experiencing booster high current failure<\/strong>, you can get a current protector apparatus for your socket. You can follow the steps below for the booster low current error solution:<\/p>\n\n\n\n\nFirst, check the electrical connection of your booster and make sure that the power is not cut off.<\/li>\n\n\n\n If the electrical connection is correct, you should contact a specialist to check the low current setting<\/strong>.<\/li>\n\n\n\nThe low current setting varies depending on the purpose of your booster and your needs. Therefore, it is important to make the correct setting by consulting your booster’s user manual or consulting a specialist<\/strong>.<\/li>\n<\/ul>\n\n\n\nBooster Blown Fuse<\/h2>\n\n\n\n A booster fuse blowout refers to a problem that prevents or affects the operation of the booster<\/strong>. This type of malfunction is caused by a problem with<\/strong> the booster’s electrical connection<\/strong> or there is a fault with the booster’s electronic board.<\/p>\n\n\n\nHow Do I Connect a Power Cable to a Water pump?<\/h2>\n\n\n\n<\/video><\/figure>\n\n\n\nBooster Phase Error Solution<\/h2>\n\n\n\n A booster phase failure is an electrical fault in a booster system. You can follow the steps below for the booster phase error solution:<\/p>\n\n\n\n
\nFirst, check the electrical connection of your booster and make sure that the power is not cut off.<\/li>\n\n\n\n If the electrical connection is correct, you may need to contact<\/strong> an electrician<\/strong> to check for a phase fault. You should always have your power line checked for a missing phase.<\/li>\n\n\n\nIn the event of a booster phase failure, it is important to contact a specialist<\/strong> to ensure the operation of your booster .<\/strong><\/li>\n<\/ul>\n\n\n\nBooster Failures Leaking Water<\/h2>\n\n\n\n A booster water leak causes the booster to lose water pressure and water is wasted. You can follow the steps below to prevent booster water leakage:<\/p>\n\n\n\n
\nCheck for water leakage in the body or connection points of your booster.<\/li>\n\n\n\n If your booster is leaking water, the seals or valves<\/strong> in your booster need to be replaced<\/strong>.<\/li>\n\n\n\nIf the water leakage problem in your booster continues, it is important to contact a specialist.<\/li>\n<\/ul>\n\n\n\nHydromat Failures<\/h2>\n\n\n\n A hydromat is a device attached to the discharge nozzle of a booster<\/strong>. What does a hydromat do? It automates the booster. The malfunctions and solutions of the hydromat are different.<\/p>\n\n\n\nTo learn more about booster automatics malfunction, hydromat repair, I recommend that you consult a specialist according to the brand and model of the hydromat.<\/p>\n\n\n\n
Since<\/strong> hydromats are resistant to dry running<\/strong>, they are connected to the network<\/strong> without the need for a tank and have a permanent check valve <\/strong>under their bodies.<\/p>\n\n\n\nHydromats, usually do not dampen water and are odorless. <\/strong>They also require no maintenance and operate silently. Hydromats allow the pump to be automatically started or stopped<\/strong> according to the water demand.<\/p>\n\n\n\nHydromat malfunctions such as hydromat not activating, hydromat running continuously may be the following:<\/p>\n\n\n\n
\nThere is a leakage greater than 70 liters\/hour flow rate at any point of the installation<\/strong>.<\/li>\n\n\n\nThe manual start button (RESET) is stuck<\/strong>.<\/li>\n\n\n\nElectronic board failure<\/strong>.<\/li>\n\n\n\nFaulty electrical connection<\/strong><\/li>\n<\/ul>\n\n\n\nHow to Adjust Hydromat Pressure<\/h2>\n\n\n\n You can follow the steps below to adjust the hydromat pressure:<\/p>\n\n\n\n
\nFirst, cut off the water pressure and allow some time to wait.<\/strong><\/li>\n\n\n\nWait until you reach the pressure level<\/strong> you want to set .<\/strong><\/li>\n\n\n\nClose the tap and using an insulated screwdriver<\/strong> you can loosen the halt screw<\/strong> by tightening it.<\/li>\n\n\n\nAfter completion, check the water pressure.<\/li>\n<\/ul>\n\n\n\nWhat happens if the booster runs without water<\/h2>\n\n\n\n When the booster operates without water, the booster gives a no water fault. The booster’s automatics make the impeller rotate faster. This can lead to overheating of the bearing shaft and other components.<\/strong> It can also cause the impeller parts<\/strong> in contact with the shaft to melt, causing the impeller to stick to the shaft and prevent the shaft from moving.<\/strong><\/p>\n\n\n\nIn cases where your booster does not flood<\/strong>, you can follow the steps below to prevent your booster from malfunctioning:<\/p>\n\n\n\n\nCheck the electrical connection of your booster and make sure that the power is not cut off<\/strong>.<\/li>\n\n\n\nIf the electrical connection is correct, check that your booster is not flooding. Check that the water in the tank may be out and you can solve the problem by filling the tank with water.<\/strong><\/li>\n\n\n\nIf your booster is still not working, the booster may be sucking air from the inlet.<\/strong> The float may be faulty or the valve in the suction line may be closed<\/strong> or a clogged filter<\/strong> may be causing the problem.<\/li>\n\n\n\nIn some cases, an air fault may occur in the pump.<\/strong> If the pump is already producing air, the booster may not pump water.<\/li>\n<\/ul>\n\n\n\nIf your booster is still not working or if problems persist, it is important to contact a specialist. Experts will be able to identify the fault in your booster and carry out the necessary repairs.<\/p>\n\n\n\n
I hope this information helps! Do you have any other questions? Please share your booster malfunctions and booster problems with us in the comments section.<\/p>\n\n\n\n